Nanjing GS-mach Extrusion Equipment Co.,Ltd
24H Hotline:+86-18851021602 +86-15195907172
Place of Origin: | Made in Nanjing |
Brand Name: | GS-mach |
Certification: | CE SGS |
Model Number: | GSJ-65/150 |
Minimum Order Quantity: | 1 |
---|---|
Price: | negotiation |
Packaging Details: | Wooden base plate, damp proof plastic lining, fully-closed plate-box external |
Delivery Time: | 45 days after payment of deposit |
Supply Ability: | 100 set/ month |
Process Material: | PVC Cable Material | Pelletizing System: | Air Cooling Hot Cutting System |
---|---|---|---|
Twin Screw Diameter: | 65 Mm | Single Screw Diameter: | 150 Mm |
Mixer: | 110L Kneader | Capacity: | 500-600 Kg/h |
Granules PVC pelletizing granulator Air cooling hot cutting granulation machine
PVC shrinkage film manufacturers used sieving to make the size of PVC resin powder uniform and easy to operate. When the particles are large, the plasticizing temperature is high, the time is long, the plasticizer takes more time, the small size of the particles is short, the plasticizing time is low, the plasticizing time is short, the particle size is too wide and the plasticizing temperature and time are not easy to control. Therefore, PVC resin powder should be sieved before PVC granulation, so as to remove excessive PVC particles.
In order to make PVC mix well with various auxiliaries, two kinds of equipment, Z low speed kneader and high-speed kneading machine, can be used for plastic products factories. The Z kneader is made up of a semicircle shaped slot and a switchable lid and a Z type spiral slowly rotating blade. The slot jacket can be heated by steam or electric heating. After the work is finished, it can be turned over and poured out of the mixed plastic in the tank. The high speed kneader consists of two parts: one on the bench, a stainless steel pot, a pot cover and a rotating shaft with a stirring paddle. Through the direct connection with the motor, the blade of the stirred blade can be rotated at high speed under 1408r/min, and the friction force will increase the PVC formula to 3~5min. After that, the temperature can rise to 90~100 C, then enter the low stirring pot, stir at low speed, then cool down with cooling water in the jacket, then discharge.
Extrusion molding principle
1. Analysis of extrusion process
-----temperature
There are two main sources of heat, one is the heat produced by shearing and friction of materials and materials, the other is the heat provided by external heaters. It should be pointed out that the design of the barrel and screw has great influence on the heat generation during the extrusion process.
-----pressure
The pressure peak value of the conventional screw pressure profile is located at the beginning of the metering section (or around it). The new screw pressure contour line, the pressure contour curve of the IKV extrusion system with longitudinal grooves on the inner wall of the charging section. The peak pressure is in the compression section.
Machine introduction
Model | Machine | Quantity |
1 | 200L high speed mixer | 1 set |
2 | Spiral feeder | 1 set |
3 | Twin screw metering feeder | 1 set |
4 | GS-65 twin screw extruder | 1 set |
5 | Connector | 1 set |
6 | GSD-150 single screw extruder | 1 set |
7 | hydraulic plate automatic screen changer | 1 set |
8 | Air cooling hot cutting system | 1 set |
The extrusion granulator unit is highly integrated with high level of automation and control. Therefore, there will be more difficult to diagnose in the actual operation, which leads to too long processing time, which will affect the normal operation of the whole set of polypropylene plant and greatly reduce the economic benefit of production. Based on the theoretical knowledge of the extrusion granulation process and the management experience of more than ten years of actual production operation, the author analyzes and judges the common causes of the failure in the operation of the unit, and makes the corresponding solutions and treatment methods so as to ensure the stable operation of the long period.
Main Technical Parameters:
Kneader | Capacity | 110L |
Output | 100-140 kg/batch | |
Motor power | 180 kw | |
GS-75 twin screw extruder | Main motor power | 132 kw |
screw diameter | 71 mm | |
Screw L/D | 36:1 | |
GSD-180 single screw extruder | Main motor power | 75kw |
Screw diameter | 180 mm | |
screw L/D | 9:1 |
After-sale service & Technical support:
Pre-sales services
* Any concerns of our machine by email/phone will be replied ASAP within 24 hours
* Inquiry and consulting support
* Quick reply.
* View our factory
After-sales service
* Traning how to install the machine, training how to use the machine
* Engineers are available to service machinery overseas
* One year guarantee for the machine expect the spare part, we can supply lifelong technology service to solve any problem form you.
Contact
Nanjing GS-mach Extrusion Equipment Co., Ltd
No.12 Shanghu Industrial Park,Jiangning Street, Jiangning District, Nanjing China
Mobile Phone/ Whatsapp: +86 18851021602
Tel: 86-25-81030382-8:00~17:00
Fax: 86-25-52790852
Email: extruder5@njgsmach.com
Web: http://www.plasticpelletextruder.com
Product Picture: